- Articles & Information Index
- Glossary
- A brief guide to setting your camera
- Ball Clamp Maintenance
- Engineering
- Gallery & general interest
- Lens tests
- Lighting & Colour
- Maintenance
- Nikonos info.
- Optics & Imaging
- Starting out
- Underwater connectors

by David W Knight (Cameras Underwater)

The focal point of a lens is the point at which light from an object at infinite distance is made to converge. Since an underwater dome port is a diverging lens, the focal length is strictly negative (the image is virtual), but we will treat it as a positive quantity here because the intention is to derive an expression which can be used to estimate the distance from the camera to the virtual image.

In standard UW photographic practice with lenses of moderate to wide FOV, an attempt is made to place the lens entrance pupil at the centre of curvature of the dome. This choice ensures that rays normal to the dome surface are undeflected on their path to the lens, thereby making the FOV underwater the same as it is in air. Note however that pupil positioning is rarely accurate when using an interchangeable lens camera, being dependent on generally limited choices for port extension length, and being subject to the fact that the camera is always mounted (inside the housing) in the same place, regardless of which lens is in use. Thus, although we must assume that the lens is in the right place for the purposes of theory, it is important to be aware that incorrect positioning will introduce error in practice.

In the diagram below, the entrance pupil of a camera lens is placed at the centre of curvarure C of an air-filled thin-walled dome of radius r which is immersed in water. A ray travelling along the lens axis is undeflected and goes straight to the camera, but an off axis ray is deflected through an angle φ. Thus rays from infinity appear to come from a point F (the secondary focus). If the camera lens is to be able to focus on the virtual image at F, it must have a minimum focusing distance of ≤ s + b (where b is the back-focal distance).

Using the Sine rule:

s / Sin(180-θ

but Sin(180-θ) = Sinθ

Therefore

s / Sinθ

In the small angle limit, Sinθ → θ , therefore

s = r θ

but, by inspection, φ = θ

s = r θ

Factoring θ

s = r / ( 1 - θ

By Snell's law of refraction:

n

(where n

θ

substituting this into (1) gives:

s = r / (1 - n_{a}/n_{w }) |

s = 4r |

In practice, the use of very thin domes is not possible in pressure-resistant underwater housings. If the dome has finite thickness, and is made of material having a refractive index greater than that of water (such as glass or acrylic), then the virtual image will be moved slightly closer to the camera. Thus the minimum focusing requirement is a little more severe than the simple 4r rule would seem to imply.

The derivation of the focal distance for the general case is somewhat more tricky than the thin-wall approximation, but we can start by analysing the passage of a light ray striking the port at an arbitrary angle.

In the diagram above, an incident ray (in water) meets the port surface at an angle θ

n

As the ray traverses the port to strike the inner surface, the normal to the surface undergoes an angular displacement δ . Hence the angle of incidence at the inner surface is θ

n

By inspection of the diagram; using the Sine rule we get:

Sin(180 - θ

Where r is the dome inner radius, and δr is the dome thickness. Now, since Sin(180-θ) = Sinθ , in the small angle limit this becomes:

(θ

Rearrangement gives:

δ = θ

Substituting this into (3) gives:

n

and using (2) to substitute for θ

θ

As shown below, an expression for the focal distance s is obtained in the same way as for the thin-walled case:

Referring to the diagram above, using the Sine rule gives:

s / Sin(180 - θ

but Sin(180 - θ) = Sinθ , and so, in the small angle limit:

s / θ

A problem which remains however, is that of eliminating φ so that s can be expressed in terms of fixed physical parameters. The solution is obtained by drawing parallels, as shown in the diagram below:

by drawing a line a - a' parallel to the line c - c' against which θ

θ

i.e.,

φ = θ

Using this in (6) gives:

s = r θ

Substituting for δ using (4) gives:

s = r θ

and substituting for θ

s = r θ

i.e.,

s = r θ

Factoring out θ

s = r / [ 1 - (θ

and substituting for θ

s = r / [1 - (n_{a} / n_{w}) {1 + (n_{w} / n_{p}) δr /r } / (1 + δr / r) ] |

Some example calculations are shown below. Accurate data were available for the ikelite 6" port, but the thicknesses of the boron crown-glass (BK7) ports are guesses. Still, the calculations give the general idea, which is that the finite thickness of the port puts the virtual image some 10 to 15mm closer to the camera than the simple 4r rule would suggest.

The infinity correction figure, in diopters, is simply the reciprocal of s in metres, i.e., it is the magnifying power required to make rays from the virtual image become parallel if the correcting lens is placed at the centre of curvature of the dome.

Don't forget to add the back focal distance b when estimating the minimum focusing distance requirement. The position of the focal plane in an interchangeable lens camera is often marked with the symbol . The position of the lens entrance pupil should be given in the data sheet, but it can also be estimated by stopping-down and noting the apparent position of the iris.

You can download the open document spreadsheet used for the calculations above and play with the numbers for yourself →

An alternative approach to the dome port formula is given here:

© Cameras Underwater Ltd. 2012

David W Knight asserts the right to be recognised as the author of this work.